Our range of condensers are currently available in three standard sizes to suit your engine capacity.
They are made from copper & brass and are of soft soldered construction.
Available complete - as pictured above - unlagged or in simple self assembly kit form
Matching
Boiler Feedwater Tanks - Available Now
| Specification |
Steam
Plant
|
|
Small - MMC01 - MMC02 - MMC03 2 inches (50mm) diameter 2 1/2 inches tall (excluding drain tap) The base is 2 1/4 inches (57mm) square M4/4BA sized mounting holes 1/4 x 40tpi drain tap for 5/32 pipe
|
For the smaller steam engine with single or twin cylinder bore sizes up to 7/16" (11mm) Ideal for all "Cheddar Models" steam engines, Pintail, Puffin, Gemini & Proteus or Stuart Turner oscillators. The kit version includes the drain tap & steam inlet & outlet unions, but does not contain the mahogany cladding or brass banding. With full assembly instruction sheet. If you require a condenser of a height size that is not listed here, please Email your requirements. The condensers can be built to a height to suit your specific application, usually retaining the standard listed price. |
|
Medium - MMC04 - MMC05 - MMC06 2 1/2 inches (64mm) diameter 3 inches tall (76mm) (excluding drain tap) The base is 2 3/4 inches (70mm) square M4/4BA sized mounting holes 5/16 x 32tpi drain tap for 3/16 pipe |
For steam engines with single or twin cylinder bore sizes up to 1 inch (25.4mm) Ideal for Stuart Turner steam engines: 10v, 10h, Double10v, Score, Beam Engine or similar. The kit version includes the drain tap & steam inlet & outlet unions, but does not contain the mahogany cladding or brass banding. With full assembly instruction sheet. If you require a condenser of a height size that is not listed here, please Email your requirements. The condensers can be built to a height to suit your specific application, usually retaining the standard listed price. |
|
Large - MMC07 - MMC08 - MMC09 3 1/2 inches (89mm) diameter 4 inches tall (excluding drain tap) The base is 3 3/4 inches (95mm) square M4/4BA sized mounting holes 3/8 x 32tpi drain tap for 1/4 pipe |
For steam engines with single or twin cylinder bore sizes 1 inch (25mm) and above Ideal for Larger Stuart Turner steam engines: Twin Launch, Compound Launch, Major Beam Engine or larger. The kit version includes the drain tap & steam inlet & outlet unions, but does not contain the mahogany cladding or brass banding. With full assembly instruction sheet. If you require a condenser of a height size that is not listed here, please Email your requirements. The condensers can be built to a height to suit your specific application, usually retaining the standard listed price. |
Our condenser/oil traps are a very useful fitting for any model steam plant, the condenser prevents water from gurgling up the boiler's chimney & keeps the surrounding area free of steam oil residue. They are an absolutely essential fitting for a model steam boat, the purpose of the condenser is to trap the oil & steam mixture as it exhausts from the engine. Without a condenser, the engine exhaust will contaminate the surface of water on which you sail, which is not acceptable. The exhaust steam & oil enters the condenser where it settles, clean steam then goes up the chimney or exhaust pipe.
The oil & water mixture then can be drained when full, by simply opening the drain tap & running the engine. This will pump out the water into a suitable container for safe disposal later. Our condensers are of silver soldered construction, clad in mahogany strip with brass banding. We can also supply the condensers in a plain black painted finish, or even just polished if required. The condensers shown below are of the twin tap type, one tap is the drain, the other closes steam off to the chimney allowing the subsequent pressure to pump out the water. Our current range of condensers are supplied with a single drain tap fitted, as exhaust back pressure is usually sufficient to pump out the condensate. Suitable copper piping with fittings can also be supplied for individual installations.
Our condensers are available fully assembled - ready to go - or in easy assembly kit form.
The above photographs show a condenser fitted in a model steamboat & as part of a marine steam plant
Above is a smaller"Cheddar" sized condenser & a larger sized condenser - these are the twin tap versions
Current Production Model - Large Condenser
Complete model steam boats built to order, model marine steam engine reversing gearboxes, model marine or stationary steam engine condenser/oil traps, steam boiler feed water reservoir tanks, steam boiler feed pumps, manual steam boiler feed hand pumps, model steam engine cylinder displacement lubricators with optional T pieces and drain bucket, model steam fittings, model steam engine nameplates in brass or composite material, model steam engine display materials, model engineering services, steam plant assembly service, steam engine display items, Vintage steam pond launch restoration and rebuilds, model marine steam plants built to order, plus The Complete Guide to Miniature Steam - available on CDROM or by direct Internet download. Used steam models for sale.
